Mivec Owners Group

It is currently 26 May 2018 09:28

All times are UTC + 12 hours [ DST ]




Post new topic Reply to topic  [ 54 posts ]  Go to page Previous  1, 2, 3, 4  Next
Author Message
PostPosted: 16 Dec 2014 20:14 
Offline
Mivec Guru

Joined: 04 Jul 2005 13:25
Posts: 1207
Location: Lower Hutt
Country: NZ
Did you degree the cams?
They look a bit "out".
6 deg at the cam, that's a whole 12 deg at the crank.
Hope you replaced that vac hose too, it'll be leaking soon.

There should be a pulley between the crank gear and intake gear?
That should have a flange on it?That guides the belt up to the cam gear?
Unless the gears aren't right.

Steve

_________________
6G72 mivec Twin TDO5 20Gs up and running.
Scrapheap special making exactly 280 horses at some unknown rpm.
Engine dyno under construction.

It's easier to fool someone than it is to convince someone that they've been fooled.


Top
 Profile  
 
PostPosted: 16 Dec 2014 23:27 
Offline

Joined: 31 Jul 2013 17:15
Posts: 40
Country: Malaysia
The picture showing is early stage prototype ITB flange & angle adapter
& thanks to the advise..


Top
 Profile  
 
PostPosted: 08 Jan 2015 07:08 
Offline

Joined: 31 Jul 2013 17:15
Posts: 40
Country: Malaysia
Prototype Brake deflector @ brake ducting
- For better circulation cold air to rotor


Attachments:
IMG-20150106-WA0002.jpg
IMG-20150106-WA0002.jpg [ 65.88 KiB | Viewed 3642 times ]
IMG-20150106-WA0001.jpg
IMG-20150106-WA0001.jpg [ 68.25 KiB | Viewed 3642 times ]
IMG-20150106-WA0000.jpg
IMG-20150106-WA0000.jpg [ 67.54 KiB | Viewed 3642 times ]
Top
 Profile  
 
PostPosted: 16 Jan 2015 16:24 
Offline

Joined: 31 Jul 2013 17:15
Posts: 40
Country: Malaysia
Advanti wheel S1
- water transfer printing carbon fibre look


Attachments:
IMG-20150115-WA0004.jpg
IMG-20150115-WA0004.jpg [ 92.82 KiB | Viewed 3616 times ]
IMG-20150115-WA0005.jpg
IMG-20150115-WA0005.jpg [ 116.07 KiB | Viewed 3616 times ]
Top
 Profile  
 
PostPosted: 11 Feb 2015 19:00 
Offline

Joined: 31 Jul 2013 17:15
Posts: 40
Country: Malaysia
Setting up..
corner weight , ride height & alignment


Attachments:
IMG-20150115-WA0007.jpg
IMG-20150115-WA0007.jpg [ 89.46 KiB | Viewed 3544 times ]
IMG-20150115-WA0006.jpg
IMG-20150115-WA0006.jpg [ 92.31 KiB | Viewed 3544 times ]
Top
 Profile  
 
PostPosted: 16 Mar 2015 22:50 
Offline

Joined: 31 Jul 2013 17:15
Posts: 40
Country: Malaysia
Just for sharing..
50% data corner weight & aligment for my car..
- weight with full interior compartment & 25liter gasoline
except spare tyre, cd player, speaker & driver
- Coilover GAB SS 32step damping with pillowball. Spring rate 10k front , 6k rear

A.Camber
1.FR:-3.0
2.FL:-3.0
3.RR:-1.2
4.RL:-1.2

B.Toe
1.FR:-0.5mm
2.FL:-0.5mm
3.RR:+1.0mm
4.RL:+1.0mm

C.Corner Weight
1.FR:335
2.FL:325
3.RR:171
4.RL:188
Total=1019kg


Top
 Profile  
 
PostPosted: 08 Jul 2015 01:33 
Offline

Joined: 31 Jul 2013 17:15
Posts: 40
Country: Malaysia
SAME GREAT PAINT, LESS TIME SPENT PAINTING!

TIREPENZ


Attachments:
WP_20150707_13_02_08_Pro.jpg
WP_20150707_13_02_08_Pro.jpg [ 214.67 KiB | Viewed 3336 times ]
WP_20150707_13_02_22_Pro.jpg
WP_20150707_13_02_22_Pro.jpg [ 212.83 KiB | Viewed 3336 times ]
Top
 Profile  
 
PostPosted: 08 Jul 2015 01:39 
Offline

Joined: 31 Jul 2013 17:15
Posts: 40
Country: Malaysia
2015 Engine Bay...

New intake manifold setup coming soon...


Attachments:
IMG-20150106-WA0004.jpg
IMG-20150106-WA0004.jpg [ 124.73 KiB | Viewed 3335 times ]
Top
 Profile  
 
PostPosted: 09 Jul 2015 19:29 
Offline

Joined: 31 Jul 2013 17:15
Posts: 40
Country: Malaysia
4 inch Billion funnel


Attachments:
WP_20150709_13_52_49_Pro.jpg
WP_20150709_13_52_49_Pro.jpg [ 151.5 KiB | Viewed 3326 times ]
Top
 Profile  
 
PostPosted: 19 Jul 2015 02:35 
Offline

Joined: 15 Feb 2011 08:51
Posts: 901
Country: Australia
Looking really good, keep up the great work.

How come your rear spring rates are so much softer than the front?

And what Honda ball joint did you use? Did it cause any bump steer problems?

Any idea why there is such a big weight difference between the 4G93 and 4G92 MIVEC pistons?


Top
 Profile  
 
PostPosted: 19 Jul 2015 05:44 
Offline

Joined: 31 Jul 2013 17:15
Posts: 40
Country: Malaysia
Previous setup is front 6k rear 4k with OEM front , rear lower arm & bushing. Tyre AD08
track in Sepang circuit will cause car..
- lots of body roll and understeer when high & low speed corner
- diving when the car is braking
- squat when the car is throttle
- weight transfer is terible..

some video to share for above setup..

https://www.youtube.com/watch?v=fsJOAHLzdIQ
b series (camera car) trying to chase me (93 mivec) but i'm trying to chase i-vtec fd2 type R start from 5min to 8min

Using h22a accord ball joint. So far so good


Top
 Profile  
 
PostPosted: 19 Jul 2015 05:51 
Offline

Joined: 31 Jul 2013 17:15
Posts: 40
Country: Malaysia
50% job done..
Still under progress..


Attachments:
WP_20150709_13_36_31_Pro.jpg
WP_20150709_13_36_31_Pro.jpg [ 178.31 KiB | Viewed 3293 times ]
WP_20150709_13_37_17_Pro.jpg
WP_20150709_13_37_17_Pro.jpg [ 187.55 KiB | Viewed 3293 times ]
WP_20150709_13_38_55_Pro.jpg
WP_20150709_13_38_55_Pro.jpg [ 178.3 KiB | Viewed 3293 times ]
WP_20150709_13_56_55_Pro.jpg
WP_20150709_13_56_55_Pro.jpg [ 145.47 KiB | Viewed 3293 times ]
Top
 Profile  
 
PostPosted: 19 Jul 2015 13:09 
Offline

Joined: 15 Feb 2011 08:51
Posts: 901
Country: Australia
Were the Honda Accord ball joint a direct fit?
What year model is the H22A, the Type R version?
Did you make adjustments on the tie rod angle to eliminate bump steer?


Intake manifold looks really good. What do you expect to gain from it?


Top
 Profile  
 
PostPosted: 19 Jul 2015 17:57 
Offline

Joined: 31 Jul 2013 17:15
Posts: 40
Country: Malaysia
Really cant remember
All the bushing & ball joint cant' direct fit in to mitsu. front & rear arm
have to send to machine job to done it
The ball joint from honda is slighly smaller diameter compare to OEM. Have to fabricate a coller to fit in.
Have to make adjustment too but not much


Top
 Profile  
 
PostPosted: 26 Aug 2015 21:49 
Offline

Joined: 31 Jul 2013 17:15
Posts: 40
Country: Malaysia
G4 PC Link software layout gauges and perhaps data logging display
Tablet HP Stream 7 & USB to micro USB adaptor


Attachments:
WP_20150826_14_40_29_Pro.jpg
WP_20150826_14_40_29_Pro.jpg [ 110.88 KiB | Viewed 3141 times ]
WP_20150826_15_43_52_Pro.jpg
WP_20150826_15_43_52_Pro.jpg [ 141.35 KiB | Viewed 3141 times ]
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 54 posts ]  Go to page Previous  1, 2, 3, 4  Next

All times are UTC + 12 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group